The 9 Best Raspberry Pie Cooling Fan
Nowadays, there are so many products of raspberry pie cooling fan in the market and you are wondering to choose a best one. You have searched for raspberry pie cooling fan in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings raspberry pie cooling fan which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
Miuzei Raspberry Pi 3 B+ Case with Fan Cooling and 3× Heat-Sinks, 5V 2.5A Power Supply with On/Off Switch Cable for RPi 3 B+, 3B, 2b
- 9 Layers case for Raspberry Pi 3 model B+ / Raspberry pi 3 / pi 2 (Not include Pi Board)
- Case has the designed layout for the Raspberry pi 3 model b+ and will perfectly protect your pi components
- Made of Acrylic, the pi case makes sure that won’t block Pi’s Wifi / Bluetooth signal
- Accurate plugs on the case are available to connect Pi’s GPIO, HDMI, USB, SD, Power Supply etc ports
- Specially Come with mini fan and 3 pcs heatsinks for quick cooling CPU/ROM/RAM, also has a stable 2.5A power supply with a handy on/off switch on the 1.5m long cable
(The Same Case Kit for RPI 4, please go to: http://www.amazon.com/dp/B07TTN1M7G)
This is 9 layers case for raspberry pi 3 model B+, also could compatible with raspberry pi 3 /pi 2 .
1. All ports are available
Special design is easy to insert/remove SD card, allows Breakout cable, HDMI cable and other ports for RPi access.
2. Better heat dissipation performance
The mute mini cooling fan and aluminum heatsinks have stronger heat radiation while the pi board working.
3. Good quality material
The raspberry pi 3 case with clear acrylic layers is more durable to protect your RPi board!
4. Crystal-like appearance
Clear case is easy to watch the internal state while pi board working to check if all electronic components function normally.
1x Acrylic Case for Raspberry Pi 3 model B+ / 3 / 2
1x Mute Cooling Fan
1x 5V 2.5A Power Supply
3x Aluminum Heat Sinks 14*14*6mm x 2(Large) 9*9*5mm x 1 (small)
4x Metal Screws and Bolts for the case
Miuzei Raspberry Pi 3 B+ Case with Fan (The same case without power supply): http://a.co/1YTEbRO (B07C6CFL2B)
Miuzei Raspberry Pi Camera Module: http://a.co/eBHmA2y (B07BTP8VXL)
Note: Please peel off the protective films on the top and bottom layers before use, the film was tiny and not easily noticeable
Please make sure the layer 3 was installed right, if you installed it 180 degrees backwards, it will make all the difference in the power plug fitting.
(1) Small components inside, please away from young kids below 3yrs.
(2) Kindly to know this case can’t fit for ASUS tinker board.
Any question there, please don’t hesitate to contact us to get support and services via Buyer Message or Q&A
Similar items with 4 stars and above
GeeekPi Raspberry Pi 3 B+ Cooling Fan, Raspberry Pi Aluminum Heatsink Cooling Kit for Raspberry Pi 3B+ (B Plus)
- Compatible with Raspberry Pi 3 B+（B Plus）
- It’s compatible with most of cases in the market
- Use CNC Machining manufacturing technology for Aluminum heatsink
- With 2pcs little thermal tapes to attach to the CPU and LAN tightly for better dissipation
- The cooling fan updated to 3510 version and it will be more quiet and powerful for heat dissipation of Raspberry Pi Board
- NOTE:Raspberry Pi Board Not Included!
- Package Includes: 1x Cooling Kit( Aluminum Heatsink with Cooling Fan), 1x Think Copper Heatsink, 2x Thermal Tapes
Extreme Cooling Fan Kit For Raspberry Pi 3B+
3510 Version Extreme Cooling Fan Kit For Raspberry Pi 3B+ is a brandnew Cooling system for your Raspberry Pi 3B+.
It’s a completely new radiator, and it’s a very cool cooling system after the armor shell.
The fan is 3510 version and more powerful but still quite when it is running.
Two aluminum blocks will touch the MCU tightly and good for the heat dissipation.
It’s with good-looking appearance, and easy to assemble.
1x Cooling Kit( Aluminum Heatsink with Cooling Fan)
1x Thin Copper Heatsink
2x Thermal Tapes
Aokin 4 PCS Raspberry Pi Fan 30x30x7mm Cooling Fan Brushless CPU Cooling Fan Heatsink Cooler Radiator Connector Separating One-to-Two Interface 3.3V 5V for Raspberry Pi 4 Pi 3 B+, Pi 3, Pi 2, Pi 1 B+
- ????Suitable for A Variety of Products: Pi fan, 30x30x7mm Raspberry Pi zero w heatsink, suitable for Raspberry Pi 4 Pi 2/ Pi 3/3B+ and Pi Zero/Zero W, Retroflag NESPi case and Nespi Case. Not necessarily using them for Raspberry Pi but rather for cooling of a desert traversing robot project. This fan gives a smooth and quick working performance, which will provide you a perfect working space.
- ????Super Quiet: This fan will not make you feel uneasy during they are working, but also a quiet experiment environment for you. Perfect Cooling Tool: Quickly dissipate heat for your Raspberry Pi or other experimental tools to and extend the lifespan of your Pi or other development boards.
- ????Unique Terminal Interface: It with two terminals, Its connector is separating, One-to-Two interface, can choose 3.3V or 5V. According to the voltage requirements in accordance with your needs to choose to use
- Working voltage: 3.0-5.8V
- Current: 0.18A. Air volume: 5m³ / h
- Number of revolutions: 13200RPM.
- ????Installation Screws Included: Don’t need to purchase screws by yourself. Screws Included. Fast installation in seconds. Intimate service, easy to install!
- ????Sleeve fan suitable for Raspberry Pi 4 and 3 B+. One-to-Two wire connector Interface for dual speed mode (3.3V and 5V DC), Compatible with other robotic projects and development boards
Aokin 4pcs Raspberry Pi DC Brushless Cooling Fan Heatsink Cooler Radiator Connector Separating One-to-Two Interface 3.3V 5V for Raspberry Pi 4 Pi 2/Pi 3/3B+ and Pi Zero/Zero W or Other Robot Project
This Pi fan not only support Raspberry Pi 2/ Pi 3/3B+ and Pi Zero/Zero W, but compatible with other development board.
Its connector is separating, One-to-Two interface, can choose 3.3V or 5V.
Rated voltage: DC5V
Working voltage: 3.0-5.8V
Air volume: 5m³ / h
Number of revolutions: 13200RPM
Noise: 18 dB
4 * pi fan
16 * nuts M2.5
16 * screw M2.5 * 14mm
Raspberry Pi 4 Fan, iUniker Raspberry Pi 4 Heatsink Fan Single Fan Cooling Fan and RAM Copper Heatsink for Raspberry Pi 4, Raspberry Pi 4B, Raspberry Pi 4 Model B
- Lower Cost than Dual Fan, Single Fan Version Heatsink Fan
- It Can Compatible with Many Single Board Computer (Just pay attention to the Size of the Heatsink)
- Efficient drop temp of your Pi by using our heatsink fan.
- Custom 3M heat conductive strip can make sure your Pi works stable when you are overclocking.
- Upgrade bearing of this fan not only can make sure outputing a lot of wind,but also quiet enough.
– Voltage: 5V
– Current: 0.2A
– Power: 1W
– Speed: 7500rpm
– Noise: 29DBA
1x Single Cooling Heatsink Fan for CPU with Thermal Tape
3x Heatsinks with Thermal Tape
Smraza Compatible with Raspberry Pi 4 Fan with 4PCS Aluminum Heatsinks, DC 5V Cooling Fan for Raspberry Pi 4, Fan for Raspberry Pi 4 Model B, 3 B+, Pi 3, Pi 2, Size:30x30mm (Black Fan)
- Cooling fan fits perfectly for Raspberry Pi 4 Model B. Also compatible with Raspberry Pi 3 B+, Pi 3.
- The quiet cooling fan and 4 pcs heatsinks are good for heat dissipation of raspberry pi board.
- The Raspberry Pi 4 fan is easy to install the fan for pi by screws, the heatsinks with adhesive on the back.
- Cooling Fan Size (L x W x H): 30 x 30 x 7 mm.
- 100% CUSTOMER SATISFACTION GUARANTEED – If for ANY reason you aren’t completely satisfied with the fan, please let us know and we will give you a satisfy solution.
1. Fan compatible with Raspberry Pi 4 Model B, Pi 3 B+, Pi 3, Pi 2 Model B.
2. Significantly reduce the temperature of the CPU.
3. Almost without any noise.
4. Stable and big wind force.
5. With screws and screw nuts, easy and simple to install.
1) Mini fan x1
2) Aluminum heatsinks x4
Pi 4 Case, Raspberry Pi 4 Armor Case Metal Case with Dual Fan Aluminium Alloy, Raspberry Pi 4 Fan, Pi 4 Heatsink for Raspberry Pi 4 Model/Pi 4B
- Updated Manufacturing Process with Improved CNC Aluminium Alloy Quality
- Cool Design and Nice Looking Raspberry Pi Case With Dual Fan
- GPIO and all Main Connectors are easily access to use
- Comes with MazerPi Dual Cooling Fan
- No More Overheating Problem
- Comes With High Quality Thermal Tape
For Dual Fan:
– Low Power Consumption Design
– Dual Cooling Expericnce, No More Overheating Problem
– Very Quiet Cooling Fan, You Can Hear Even Nothing
– All of the Fans were Tested by Our Engineer, Very Nice Quality Control
– Update Thermal Tape Can Make Sure Best Heat Conduction Effect
For Aluminium Alloy Case and Heatsink:
– Perfect Size for Raspberry Pi 4 Model B
– Big Size Heatsink and Cooling Fan Can Make Sure: No More Overheating Problem
– High Quality CNC Aluminium Alloy Case Can Protect your Pi Safe
– Open Design Can Make Sure Our CNC Case will not effect Wifi Signal
1x CNC Aluminium Alloy Case With Dual Fan
1x Screw Set
1x Thermal Tape
Notice: Raspberry Pi is NOT Included
Miuzei Case for Raspberry Pi 4 with Cooling Fan, 4 × Aluminum Heatsinks, 5V 3A USB-C Power Supply with ON/Off Switch for Raspberry Pi 4 Model B
- – 9 Layers case for Raspberry Pi 4 Model B, perfectly protect your pi components(Raspberry Pi board is not included)
- – Accurate plugs on the case are available to connect Pi’s GPIO, HDMI, Micro USB, SD Card, Power Supply etc ports
- – Made of Acrylic, the pi case makes sure that won’t block Pi’s Wifi / Bluetooth signal
- – Especially with mini fan and 4 aluminum heatsinks for fast cooling of CPU, GPU and RAM
- – Stable 3A power supply with a handy on/off switch on the 1.5m long cable. Package Included: Raspberry Pi 4 Case, 3A USB-C Power Supply, Fan, 4 Pcs Heatsinks, Rubber Feet. 【Please peel off the protective films on the top and bottom layers before use, the film was tiny and not easily noticeable】
Raspberry Pi Fan, iUniker Raspberry Pi Cooling Fan 30x30x7mm Brushless CPU Cooling Fan for Raspberry Pi 3 B+, Pi 3, Pi 2, Pi 1 B+, RetroFlag NESPI Case(2-Pack)
- Fits RetroFlag NESPI Case Perfectly.
- Upgrade bearing of this fan not only can make sure outputing a lot of wind,but also quiet enough.
- Completely solve the overheating problem of you Pi.
- Comes with screw sets.
- Efficient drop temp of your Pi by using our fan.
Suitable for Raspberry Pi B / Raspberry Pi B+ / Raspberry Pi A+ / Raspberry Pi 2 and Pi 3 Model B / Raspberry Pi 3 B+
Bearing Type: Sleeve
Size (L x W x H): 3 x 3 x 0.7 cm
Connector: 2 pin
Rated Voltage: DC 3.0-5.8V
Noise Level: 18dba±10%
Wire Length: 60 mm
2x iUniker Cooling Fan
2x Screw Sets
Argon ONE Raspberry Pi 4 Case with Cooling Fan | Aluminum Heatsink | Power Button | Supports Retro Gaming, Movies, and Music | for Raspberry Pi 4 Model B
- SLEEK ALUMINUM ENCLOSURE | Made with aluminum alloy and polished with a modern Space Grey finish for stunning aesthetics and functionality.
- PASSIVE AND ACTIVE COOLING | The whole case top acts as a passive cooling for the Raspberry Pi. And a software controllable fan is added inside the case for better temperature management.
- EASY ASSEMBLY & NEAT CABLE MANAGEMENT | Assembling the case with the Raspberry Pi is easy. Installing the Argon ONE Script that unlocks the full functionality of the Argon ONE in one line. All of the ports are accessed at the back, making the mini-computer manageable with minimal cable clutter and easy cleaning.
- PROPER SYSTEM SHUTDOWN | A proper power button is installed on the case to prevent file damage. It safely Shutdowns, Reboots, and Forced Shutdowns functions are built in features.
- MAGNETIC REMOVABLE TOP & ACCESS TO GPIO | The PCB Board built into the case provides separate power sources to the fan and power switch, as well as extending the GPIO pins to use the case in multiple projects.
By our suggestions above, we hope that you can found raspberry pie cooling fan for you.Please don’t forget to share your experience by comment in this post. Thank you!
Best raspberry pie cooling fan: Top-Rated Brands & What to Buy