infratechplus 
Nowadays, there are so many products of clear water filter housing 10 x 2.5 in the market and you are wondering to choose a best one. You have searched for clear water filter housing 10 x 2.5 in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings clear water filter housing 10 x 2.5 which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
Pentek 150071 3/4" #10 Standard Clear Filter Housing with Pressure Relief
- Standard filter housing for residential, commercial, and industrial applications
- Clear styrene-acrylonitrile (SAN) for on-site viewing of flow and cartridge condition
- Holds a 10″ x 2-1/2″ sediment or carbon filter cartridge (sold separately)
- Pressure relief button for easier cartridge replacement
- Initial pressure drop of 1 psi at a flow rate of 10 gpm
This Pentek 150071 3/4″ #10 Standard clear filter housing with pressure relief is suitable for residential, commercial, and industrial applications. The sump is made of clear styrene-acrylonitrile (SAN) for on-site viewing of flow and cartridge condition, and the cap is made of reinforced blue polypropylene for strength and resistance to chemicals. The cap has 3/4″ female National Pipe Thread Taper (NPT) threaded input and output connections and a nitrile butadiene rubber (Buna-N) O-ring to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. The housing can be used with a 10″ x 2-1/2″ sediment or carbon filter cartridge (sold separately). It has an initial pressure drop of 1 pound per square inch (psi) at a flow rate of 10 gallons per minute (gpm), a maximum operating pressure of 125 psi, and a maximum operating temperature of 125 degrees F (51.7 degrees C). This filter housing meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is for use in various applications, including residential drinking water filtration, food service, and humidifying systems, among others.
Specifications
| Filter cartridge size (H x W) (sold separately) | 10 x 2-1/2 inches (254 x 63.5 mm) |
| Initial pressure drop at 10 gpm | 1 psi |
| Maximum temperature | 125 degrees F (51.7 degrees C) |
| Maximum pressure | 125 psi |
| Maximum dimensions (H x W) | 12-5/8 x 5-1/4 inches (321 x 133 mm) |
| Materials and structural integrity certification | NSF/ANSI standard 42 |
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek 158643 3/8" #10 3G Slim Line Clear Filter Housing with Bracket and Pressure Relief
- Slim filter housing for low-flow applications with space restrictions
- Clear styrene-acrylonitrile (SAN) for on-site viewing of flow and cartridge condition
- Holds a 10″ x 2-1/2″ sediment or carbon filter cartridge (sold separately)
- Pressure relief button for easier cartridge replacement
- Initial pressure drop of 2 psi at a flow rate of 5 gpm
This Pentek 158643 3/8″ #10 3G Slim Line clear filter housing with integrated mounting bracket and pressure relief is suitable for low flow rate applications that have space restrictions. The sump is made of clear styrene-acrylonitrile (SAN) for on-site viewing of flow and cartridge condition, and the cap is made of reinforced blue polypropylene for strength and resistance to chemicals. The cap has 3/8″ female National Pipe Thread Taper (NPT) threaded input and output connections and a nitrile butadiene rubber (Buna-N) O-ring to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. The housing can be used with a 10″ x 2-1/2″ sediment or carbon filter cartridge (sold separately). It has an initial pressure drop of 2 pounds per square inch (psi) at a flow rate of 5 gallons per minute (gpm), a maximum operating pressure of 125 psi, and a maximum operating temperature of 125 degrees F (51.7 degrees C). This filter housing meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is for use in various applications, including residential drinking water filtration, food service, and humidifying systems, among others.
Specifications
| Filter cartridge size (H x W) (sold separately) | 10 x 2-1/2 inches (254 x 63.5 mm) |
| Initial pressure drop at 5 gpm | 2 psi |
| Maximum temperature | 125 degrees F (51.7 degrees C) |
| Maximum pressure | 125 psi |
| Maximum dimensions (H x W) | 13-3/8 x 5-3/8 inches (340 x 137 mm) |
| Materials and structural integrity certification | NSF/ANSI standard 42 |
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Similar items with 4 stars and above
Geekpure Filter Housing 10" for Reverse Osmosis System -1/4 Inch Inlet/Outlet-for 2.5 Inch x 10 Inch Fitlers
- Replacement housing for Geekpure RO system,Widely used in RO system or pre-filtration.
- Fit with most RO systems using standard 10″ filters.But different brand,the injection mould is totally different,NOTE:PLEASE REPLACE HEAD AND HOUSING BODY TOGETHER.
- INLET-OUTLET-1/4″ female threaded in and out fittings.matched quick fitting ASIN:B078VQN6TZ .
- SIMPLE INSTALLATION-Easy to replace.Food grade Polyethylene will not cause pollution to water.
- Pack of 3. 1 x Filter housing , 2 x O rings . matched wrench ASIN: B07D9JWRYQ .
Geekpure Filter Housing 10" for Reverse Osmosis System -1/4 Inch Inlet/Outlet-for 2.5 Inch x 10 Inch Fitlers Clear Housing
- FUNCTION-Replacement housing for RO system,Widely used in RO system or pre-filtration.Clear housing allows you to see when you need to change filters and everything else works as it should.
- UNIVERSAL-Standard size for most RO systems using standard 10″ filters.
- INLET-OUTLET-1/4″ female threaded in and out fittings. NOTE:PLEASE REPLACE HEAD AND HOUSING BODY TOGETHER.
- SIMPLE INSTALLATION-Easy to replace.Food grade AS will not cause pollution to water.
- Just Housing in the box, matched wrench ASIN: B07D9JWRYQ ,matched quick fitting ASIN:B078VQN6TZ .
Geekpure 20-Inch Standard Slim Line Clear Filter Housing for Whole House Water Filtration-2.5" x 20" -Inlet/Outlet 3/4" NPT Brass
- COMPLETE-Complete 1 set 20 inch blue housing,3/4 inch ports with pressure relief button for high pressure,with plastic wrench and metal bracket.
- STANDARD-Fits all standard sized 2.5 inch x 20 inch filters.Housing only, filter cartridges are sold separately.
- APPLICATIONS-Large capacity housing for high flow applications,Used in whole house, reverse osmosis, commercial and geekpure filtration.
- Clear housing allows you to see when you need to change filters and everything else works as it should.
- Flow rate: 5-10 GPM (Depend on Feed Water Pressure),Shelf life: 5 Years.
10 inch Transparent Standard Water Filter Housing, Presser Relief Button, 3/4” Inlet/Outlet Brass Port, Accepts Standard 10”x 2.5” Cartridges, 3/4” Brass Port, Mounting Hardware Included (2 Sets)
- ???? DURABLE STRUCTURE: 10” Transparent Standard Housing is proper for heavy sediment applications. The housing body is made of reinforced polypropylene for strength and resistance to chemicals, and the blue cap is made of high-flow polypropylene for toughness. The cap has 3/4″ inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes
- ???? POINT OF USE: Those Housings for use in various high-flow applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, well water filtration, food service, and irrigation. Extends life of Washing Machines, Water Heaters & Other Household Appliances Removing Chlorine, Taste, Odors & Other Particles
- ???? EASY TO OPERATE: There is rubber O-ring on the top of the housing body to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. Unique cap design allow quickly and easy to remove housing to replace cartridges. Transparent housing body allows visually to determine when cartridge should be changed
- ????ACCEPTS 10” Standard Cartridges: Dupont PFC5002, WFPFC5002, Pentek DGD Series, 3M CFS110, CBC-10, Aqua Pure AP110, AP51T, Hydronix SGC-25-1005, Culligan P5, D-10A, OmniFilter RS14-SD, GE FXUSC, Aquaboon 25S-5M, Manitowoc K-00173, Whirlpool WHKF-GD05, WHA2BF5, American Plumber W5P, Watts Premier MAXETW-975, WCBCS975-RV, SCWH-5, Tier1 EP5_10, EcoPure EPW2C, Purenex C-5M, KleenWater KWGE25RG, Omnipure OMB934-5M, WFPFC9001, MatriKX E32-250-125-975, DEV9108-15, iSpring FC15 (Sold Separately)
- ???? WELL-MATCHED FOLLOWING HOUSINGS SYSTEMS: DuPont WFPF38001C, WFPF13003B, Pentek 158643 3/8, Culligan WTR Filter HF-360A and HF-150A, American Plumber WC34-PR, Geekpure RO5-FH10, Hydronix HF3-10CLBK34, EcoPure EPW2
Similar items with 4 stars and above
iSpring HC12X2 1/4” Slimline Water Filter Housing Clear for Reverse Osmosis System 2.5 Inch x 10 Inch Filters, Clear, Pack of 2
- Industry Standard Water Filter Housing – Transparent (The cap can be in BLACK color depending on stock)
- Good for Reverse Osmosis Water Filter and RO DI Filter
- Fits 10″x2.5 standard filter cartridges, compatible to most RO systems, includes Watts Premier, Flowmatic, PuROLine, Crystal Quest, Apec, and etc.
- 1/4″ Inlet / Outlet
- Made of 100% high-quality polypropylene
Product Description
Industry Standard Water Filter Housing – Transparent (The cap can be in BLACK color depending on stock).
From the Manufacturer
Industry Standard Water Filter Housing – Transparent (The cap can be in BLACK color depending on stock)
Hydronix HF2-10CLWH12 10" Clear Body, White Flat Cap 1/2"
Refillable, Empty Water Filter Cartridge Universal Slimline (2.5" D x 10" H) Clear by CuZn
Manufactured by the most trusted brand in Water Filtration, CuZn Water Filtration Systems (est. 1987). Theses cartridge are compliant with NSF 61 Standards for use in potable & non potable water filtration systems. Materials of Construction- End Caps: High Impact Polystyrene, Body: High Impact Polystyrene, Resin: Tairirex Polystyrene.
Similar items with 4 stars and above
Express Water Clear Double O Ring Standards 10" Filter Housing for RO Reverse Osmosis System – 3 Pack
- Simply Pure – Keep your water clean, odorless, and tasteless with 100% food grade BPA free polycarbonate housing three set
- The Highest Quality – Heavy duty, durable, reuseable, leak free threaded housing connections
- Quick Connect Compatible – Can connect directly to any 1/4″ threaded male push or quick connection
- Universal Standard – Use with Reverse Osmosis Systems at 50, 75, 90, 100, 125, or 150 Gallons per Day
- The Reliable Choice – Works with hot and cold water! For use with temperatures from 33°F to 140°F
Conclusion
By our suggestions above, we hope that you can found clear water filter housing 10 x 2.5 for you.Please don’t forget to share your experience by comment in this post. Thank you!
