infratechplus 
Nowadays, there are so many products of small heating cable in the market and you are wondering to choose a best one. You have searched for small heating cable in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings small heating cable which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
HEATIT HISD 30-feet Pipe Heating Cable with Built-in Thermostat
- Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact our customer service in any time, we’ll try our best to solve your issues.
- Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
- Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
- Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight.
- Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
Similar items with 4 stars and above
Frost King HC12A Heating Cables, 12 Feet, Black
Frost King HC12A Heating Cables, 12 Feet, Black
Similar items with 4 stars and above
HEATIT JHSF 120-feet 120V Self Regulating Pre-assembled Pipe Heating Cable
- JHSF doesn’t work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment. HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com).
- Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
- Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off), and instructions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2″ in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
- ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. The minimum bending radius is 1 inch.Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
- Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue
PHOENIX CABLES USA Pro Cold Weather Valve and Water Pipe Heating Cable/Multi-use for rigid plastic or metal pipes, preventing RV hose freezing or down a gutter downspout (9 Feet)
- QUICK AND EASY INSTALL – No more confusing instructions! Set it up and forget it with confidence the first time around with our easy to understand BONUS eBOOK. Our heat tape for water pipes install effortlessly for constant water flowing down to -40° F (-40° C) without monitoring thanks to the built-in thermostat. Rest assured as the indicator light let’s you know your Phoenix heating cable is ready to take on the harshest seasons.
- SAVE THOUSANDS ON COSTLY REPAIRS – Don’t wait before it’s too late and get stuck paying thousands of dollars on unexpected repairs that could be avoided. Our high-grade cables are tough and durable enough for rigid plastic and metal pipes up to 1. 5” (38mm) in diameter. With our trace heat cables you’ll always stay prepared for the unexpected.
- SAVE MONEY ON ENERGY AND – 120 Volt, 7 watts/ft. and only use 5 amps or less of electricity making our heating cables for a low economical footprint. Saves you money by using less energy by powering the cable only when needed by automatically turning on below 38° F (3° C) and off above 45° F (7 ° C).
- SAFETY TESTED FOR ALL SEASONS – Compromise elsewhere when it comes to the safety of your home. Get peace of mind with our safety rated cables constructed with a continuous ground braid with a tough and durable polyurethane inner insulation and weather resistant PVC (high-low temperature) for outer protective jacket. Approved for water filled plastic (including PEX) and metal pipes only.
- UL APPROVED, CSA CERTIFIED – Made of superior industrial grade heat shrinkage tube for connection, our cable is considered to be the safest per industry standards. Set up includes: heating cable, grounded plug, built-in automatic thermostat and easy to understand instructions. Our cables plug into a standard 120 VAC outlet.
NO MORE FROZEN PIPES EVER AGAIN What so special about our water pipe heating cable? Our energy efficient cables save on costly repairs by keeping your pipes flowing – no matter how cold it gets by turning on and off automatically. No more complicated install instructions! You get our easy BONUS eBOOK to help with your one time simple and easy install for peace of mind all year long. OTHER KEY BENEFITS: WORRY-FREE AUTOMATIC THERMOSTAT Once installed – set it and forget it. The self monitoring cable turns on below 38 degrees F and off above 45 degrees F MULTI-USE FOR RIGID PLASTIC OR METAL PIPES Use on your RV water hose or down a gutter downspout; wherever you need flowing water, just install our Phoenix Heat Cable SAVES MONEY USING 70% LESS ENERGY Uses power only when needed and consumes less than 5 amps that saves you money #1 SAFETY: UL APPROVED / CSA CERTIFIED Our package includes cable, grounded LED plug that indicates that the cable is working, thermostat and an instruction manual for easy install THE FINE PRINT – 100% MONEY-BACK Our Phoenix pipe heating cable is made with high quality materials for lasting usage. We’re certain you’ll love our product or you’ll get your money back. Our cables MAKE THE PERFECT GIFT for anyone that loves the outdoors and uses RV’s so ORDER NOW! Simply click “ADD TO CART” at the top of this page to order yours today!
Prime Wire & Cable RHC1000W200 ROOF & GUTTER DE-ICING KIT ROOF HEATING CABLE
- 200 ft. Black roof & gutter de-icing kit, 1000 watts, 2 ft. 18/3 SJTW blue power cord
- Promotes water flow in gutters and downspouts
- Helps prevent water damage caused by ice dams
- Includes roof cable, shingle clips, spacers, owner’s manual & labeling for breaker & on/off switch
Roof and gutter De-Icing cables help prevent costly damage from ice Dam formation by preventing freezing of un-insulated roof eaves, Valleys, gutters and downspouts, and allows water to drain freely. This product is for use on inclined, tab-shingle roofs and in downspouts and gutters only. To ensure water can flow to the ground, cable should be installed on Unheated portions of the roof (usually the overhang) as well as in Valleys, gutter and downspouts. Roof and gutter De-Icing kits are available in lengths from 30 ft to 240 ft. These products are found as De-Icing and snow melting sets primarily in northern markets beginning in early October.
Prime Wire & Cable RHC150W30 Roof & Gutter De-Icing Kit Roof Heating Cable
- 30 ft. Black roof & gutter de-icing kit, 150 watts, 2 ft. 18/3 SJTW blue power cord
- Promotes water flow in gutters and downspouts
- Helps prevent water damage caused by ice dams
- Includes roof cable, shingle clips, spacers, owner’s manual & labeling for breaker & on/off switch
- Total Outlet: 1
Roof and gutter De-Icing cables help prevent costly damage from ice Dam formation by preventing freezing of un-insulated roof eaves, Valleys, gutters and downspouts, and allows water to drain freely. This product is for use on inclined, tab-shingle roofs and in downspouts and gutters only. To ensure water can flow to the ground, cable should be installed on Unheated portions of the roof (usually the overhang) as well as in Valleys, gutter and downspouts. Roof and gutter De-Icing kits are available in lengths from 30 ft to 240 ft. These products are found as De-Icing and snow melting sets primarily in northern markets beginning in early October.
HEATIT JHSF1-CT Self Regulating Pre-assembled Pipe Heating Cable 6-feet 120V
- HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.ETL approved.
- Fluoropolymer (Industrial grade: One of the most heavy duty plastic material) as the outer jacket. JHSF1-CT cables are configured for use in nonhazardous and hazardous locations, including areas where corrosives may be present. Exposure to organic chemicals or corrosives. Can be used underwater application. Please keep the connection (Meet water proof IP65) between the orange cold lead and black heating cable above the water level. The black heating cable including end seal meet water proof IP68
- Protect pipes up to 2 1/2″ in diameter. For a better freeze protection, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1″ thick insulation material. Pre-assembled, Including grounded plug with light, easy to install install and use without built in thermostat. 120 volt, 5 watts/ft at 50 degrees F for pipe freeze protection. 6ft 18/3 cold lead with grounded plug.
- Roof deicing application: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, composite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately.
- Testing the cable before the installation. Uncoil the cable, plug in the heating cable Normally you can feel the slight warm on the heating cable in few minutes. Ten year limited warranty – If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue.
Similar items with 4 stars and above
EasyHeat 2102 Freeze Free Heating Cable – 100′
- Self-regulating pipe heating system
- Provides flexible protection against pipe freeze-ups in even the most challenging applications
- Reduces power consumption when the pipe does not require freeze protection
- Ideal for use on residential metal or plastic water supply and drain pipes subject to freezing temperatures
- Length: 100′ and rugged metal braided jacket provides an electrical ground as well as protection against damage
EasyHeat Freeze Free self-regulating pipe heating cables provide flexible protection against pipe freeze-ups in the most challenging applications. The cut-to-length technology is ideal for installations that require protection of numerous pipes of varied lengths. The self-regulating effect of the cable reduces power consumption when the pipe does not require freeze protection. They are ideal for use on residential metal or plastic water supply and drain pipes subject to freezing temperatures; water supply lines underneath manufactured homes; and cottages, barns and outbuildings that are not regularly used.
GardenHOME Pipe and Valve Heating Cable (2X9Feet) Heat cables
- SECURED PROTECTION: From 9-11 feet (2.74-3.35 m) and up to 1-1 1/2 inches (25.4-38.1 mm) in diameter.
- EASY INSTALLATION: Just put our Icebreaker cable along the pipes to keep ice and coldness away (Recommended for use on water-filled metal and rigid plastic pipes).
- ENERGY SAVING THERMOSTAT CONTROLLED: The built-in thermostat can sense the temperature of the pipe. It turns the cable on at 38°F and turns it off automatically when the pipe has been heated to a temperature of approximately 45°F.
- ECONOMICAL: Reliable low wattage design saves up to 70% energy than other cables and protects your cable to -50°F.
- DURABLE: Weather resistant PVC outer jacket and inner insulation. It will operate for years without requiring maintenance.
Say goodbye to frozen pipes in the winter with the GardenHOME Pipe Heating Cable – 9ft. with Thermostat, designed for preventing water pipes from freezing. This temperature-controlled cable runs along the pipes and valves, thawing frozen pipes. The build-in thermostat will sense the temperature of the pipe and turn the cable on and off, while only using five amps of electricity or less, to provide the most economical solution for frozen pipe disasters.
*Our Pipe Heating Cable & Ice Melting Cable prevents your pipes from major repair costs due to cold weather, snow or frozen water damage.
*This quick and easy ice-melting kit is ideal for indoor and outdoor use.
*It is winter and Subzero resistant, durable and long lasting due to its unique material composition. This Kit prevents congestions and ice backups.
*It is easy to install by using the included mounting hardware. It operates for years without requiring maintenance.
HOW IT WORKS
It is thermostat controlled. The built-in thermostat can sense the temperature of the pipe. It turns the cable on at 38°F and turns it off automatically when the pipe is heated to a temperature of approximately 45°F.
APPLICATION AREA
Used on pipes in House, Garage, Pipes, Garden, Patio and many more!
FEATURES
• Pre-assembled for easy installation
• Protects pipes from 9-11 feet and up to 1-1.5 inches in diameter
• Use on water-filled plastic and metal pipes only
• Economical solution to frozen pipe disasters
• Weather resistant PVC outer jacket and inner insulation
ABOUT US
GardenHOME stands for highest quality to the lowest price. We give 30-days MONEY BACK PROMISE! If you are not 100% satisfied!
Similar items with 4 stars and above
TOPDURE 26.5 feet 7.5W/ft Pipe Heating Cable
- Pre- assembled with power indicator light and built in thermostat (Below 37F ON, Over 50F OFF) .
- Prevent pipe freezing down to -40° F (-40° C).
- Used on water filled rigid metal and plastic pipes.
- 7.5watt/ft 120V.Can’t be cross, spiral or overlapped.
- 6ft 18/3 cold lead with grounded plug. 2 year warranty.
Conclusion
By our suggestions above, we hope that you can found small heating cable for you.Please don’t forget to share your experience by comment in this post. Thank you!
